-350x280.jpg)
-350x280.jpg)
-350x280.jpeg)
-1000x1000.png "Large Volume Liquid Bath Model 820")
-1000x1000.jpg "Large Volume Liquid Bath Model 820")
Код: 820
Brief specifications
More details
If you have a large number of sensors to calibrate then this economically priced stirred liquid bath is the solution. The 820 bath has been introduced to provide a liquid calibration bath with a large volume. This is to allow the bath to be used with many temperature probes simultaneously immersed in the bath or with accessories. It may also be used to maintain standard resistors at a constant temperature. The liquid in the bath is heated to the set temperature and circulated by a propeller system. The Aquarium is of robust construction and the liquid is contained in a stainless steel insulated enclosure which has a calibration volume 185mm long x 140mm wide x 300mm deep. Refer to ‘Liquid Selection Guide’ on page 73 for information on liquids and important Health and Safety Information.
Large Volume Liquid Bath Model 820
- 30°C to 200°C
- If you have a large number of sensors to calibrate then this economically priced stirred liquid bath is the solution. The 820 bath has been introduced to provide a liquid calibration bath with a large volume.
- Large volume for calibration of a number of sensors,
- Good comparison accuracy ±0.01°C
Featured Products
If you have a large number of sensors to calibrate then this economically priced stirred liquid bath is the solution. The 820 bath has been introduced to provide a liquid calibration bath with a large volume. This is to allow the bath to be...
Automation of measurements using the 8500 Low Thermal Scanner allows a completely automated measurement system to be realised. Using the 8500 Scanner together with ProGraph software and the 8000 series multimeter provides a turnkey solution...
Operate confidently in cold environments, even as low as -29°C. The ruggedly designed Model 786 takes laboratory level performance into the harshest of environments.
Unlike other calibrators that cannot be used in the extreme cold, the 7...
Calibration test bench for gas meters
Calibration of domestic gas meters (G1,6…G400)
The test bench is especially designed for the calibration of domestic gas meters (diaphragm gas meters, ultrasonic gas meters, thermoelectric gas met...
The Isotech Argon Triple Point Apparatus is a robust, simple to use and affordable solution for the realisation of the argon triple point. Many laboratories use liquid nitrogen comparators which are convenient and can be low cost but the ni...
-327x226.jpeg)
Need advice on which model? Dry Block Selection Guide These models will calibrate temperature probes from -45°C to 250°C with unrivalled flexibility. As a traditional Dry Block, several thermometers can be quickly calibrated. Accessories ar...
Pneumatic hose terminated with quick fit connectors compatible with the test point adaptors supplied with the PV62XG, MC620G and the adaptor sets.
Safe area use 1 m/3.28 ft pneumatic hose. Maximum pressure 400 bar/5800 psi...
Accuracy < 2% of selected range at constant conditions
Four measurement ranges 0-1%, 0-5%, 0-10% & 0-25% O2
Sensitivity (LDL) 0.005% (50 ppm) O2
UL or ATEX certified for use in hazardous areas
Low maintenance with an average sensor life...
-327x226.jpeg)
-327x226.jpeg)
Need advice on which model? Dry Block Selection Guide These models will calibrate temperature probes from -45°C to 250°C with unrivalled flexibility. As a traditional Dry Block, several thermometers can be quickly calibrated. Accessories ar...
The Series 7050 digital pressure indicator expands upon the popular line of Series 7000 products such as the Series 7250 digital pressure controller and Series 7252 dual output pressure controller. The 7050 provides an instrument for applic...
PressCal Software
PressCal is a menu driven software program for pressure calculation and certificate generation using a deadweight tester as the pressure source. This software has been developed as a flexible working tool to make calibrat...
-327x226.jpeg)
-327x226.jpeg)
Isotech first introduced the Model 988 to assist in relation to the SARS outbreak during the early 2000s. Used to increase the accuracy of thermal imagers being used to measure human skin temperature in temperature screening of applications...
Guildline Instruments GL 1050 Series of Resistance Transfer Standards are designed as very high stability calibration laboratory transfer standards for customers looking to replace the old ESI SR1050 Series. PRODUCT FEATURES Very High Quali...
The 3000HR provides a traceable source for high voltage resistance, consisting of a buildup box of 1 GOhm and 10 Gohm resistors, allowing a buildup to 100 Gohm. High value resistance standards are required by many laboratories for calibrati...
Isotech produces a miniature resistor with ultra-low temperature coefficient and ultra-high stability. This is achieved because the resistors are oil filled and hermetically sealed. The function of hermetic sealing is to eliminate the ingre...
The new Additel 209 and 210 loop calibrator series combine ease of use and functionality, making them the ideal tools to troubleshoot your process loop. The ADT209 has an accuracy of 0.03% of reading whereas the ADT210 holds an accuracy of ...
-327x226.jpeg)
The Water Triple Point is the most important fixed point, the only point common to the ITS-90 and the Thermodynamic Temperature Scale. It is an essential reference point for every temperature laboratory. The Jarrett-Isotech cells are the be...
Pneumatic hose terminated with quick fit connectors compatible with the test point adaptors supplied with the PV62XG, MC620G and the adaptor sets.
Hazardous area use 1 m/3.28 ft pneumatic hose. Maximum pressure 400 bar/5800 psi...
The Easidew sensor is a moisture meter that measures both dew point and moisture content. It is simple to install as it is available with a wide range of process connections and electrical connectors. All Easidew dew-point transmitters are ...
A set of test point adaptors to connect the tool less quick fit PV62XG, MC620G and the extension hoses to the device under test...
