-350x280.jpg)
-350x280.jpg)
-350x280.jpeg)
Код: HC2A-S/S3/SM
Brief specifications
More details
The HC2A series are digital humidity-temperature probes based on the AirChip3000 technology. These probes
feature a UART serial interface and two 0…1 V linear analog output signals.
The HC2A probes are designed for use with the HygroClip2 generation of ROTRONIC humidity-temperature
instruments: transmitters, data loggers, hand-helds, etc.
The HC2A probes can also be used as a stand-alone device using either the analog output signals or the probe
digital interface. Connectors, cables and digital interface adapters are available to this purpose. Digital
integration with OEM applications is facilitated by the probe communication protocol options.
Humidity Temperature Probes - Rotronic HC2A-S/S3/SM
-Accuracy @23°C: ±0.8 %rh ±0.1 K
Application Range: -50..100°C; 0...100 %RH
Long term stability: <1%RH/year
Protocols: RoASCII (Default); MODBUS (setting with HW4)
Filter: Polyethylen, 40 μm; Wire mesh, 10 µm
Featured Products
The HygroSmart HS3 an advanced, digital probe with measured or calculated outputs and a rugged 10 bar pressure rated housing, designed to provide reliable humidity measurement for process control in a wide range of applications. The HS3 pro...
Isotech have a wide range of Dry Blocks to suit probes requiring a large immersion depth. These products feature large and deep calibration volumes. As such they are less portable than the earlier Dry Blocks, but have higher capacities and ...
The GPR-3500 MOVR Portable Oxygen Purity Analyzer is the only electrochemical oxygen sensor based analyzer capable of measuring 100% oxygen on a continuous 24/7 basis for the purpose of verifying the purity of medical grade oxygen transport...
As industry increasingly moves to high precision instrumentation there is an increasing need to utilise very high performance test and service equipment. Model 006-A is a laboratory accuracy six decade resistance box with a total resistance...
The XZR500 oxygen analyzer from Michell Instruments is designed to determine the excess air required for optimum combustion. It uses advanced Zirconium Oxide technology to measure levels of oxygen in harsh conditions such as boilers, incine...
The NEW 8158 Advanced Digitising Multimeter from Transmille has been designed as a modern replacement for aging multimeters without compromise. Capable of measurements at a rate of over 100,000 Samples per second, the 8158 8.5 Digit Multime...
-327x226.jpeg)
-327x226.jpeg)
Fast-Cal – the product range you designed During early 2004 20 experienced engineers from many parts of the world were asked to produce their ideal specification for industrial calibration. Their top ten requirements, in order of priority, ...
The Isotech Argon Triple Point Apparatus is a robust, simple to use and affordable solution for the realisation of the argon triple point. Many laboratories use liquid nitrogen comparators which are convenient and can be low cost but the ni...
The Local Evaluation Unit OPS is a local microcomputer designed for comparison of reference impulses coming from the standard meter with optical impulses or reflexes from the black mark on the disk of the meter. Value of the measured error ...
The Fluke Calibration 6270A
Pressure Controller/Calibrator is a robust, reliable solution that lets you dramatically simplify the task of pneumatic pressure calibration. Thanks to its modular design, it is so flexible that it can be config...
Water The Isotech B8 30 130 Cell is small enough to fit into portable Dry Blocks such as the Venus and Europa models. For the larger blocks like the Oceanus Isotech recommend the B12 46 210 with its increased immersion depth. Gallium and Me...
Designed to pre-warm and anneal Standard Platinum Resistance Thermometers Maintenance Free Use Automatic Temperature Cycling The Annealing Furnace, model 414, is designed to heat, anneal and cool Standard Platinum Resistance Thermometers (S...
Software Package ELMA is dedicated for electricity meter testing and calibration. The package contains routines for control of hardware, data acquisition, evaluation of measurements, meter data exchange, output of documents, data archiving,...
A panel mounted oxygen analyser with a remote sensor allows flexibility of installation. The GPR-1900 gas analyzer is suitable for trace oxygen measurements as low as 0-10 ppm; the GPR-2900 measures O2 up to 100%. The remote sensor block al...
Additel ACal (9530) is a powerful software package designed for varying degrees of automation of calibrations and management of your laboratory. ACal combines pressure and temperature instrument calibration automation features with laborato...
Additel’s new Multi-functional Documenting Process Calibrator series takes portability, functionality, and accuracy to a whole new level and packages it with an intuitive and easy to use color touchscreen display. This series includes an ad...
RPM4 is much more than a traditional pressure indicator
State of the art performance from very low pressure to 280 MPa (40 000 psi)… advanced on-board features…compact and rugged…full local and remote communications…RPM4 is the perfect sol...
The XTP601 Oxygen Analyzer for safe or hazardous areas is a robust, linear and stable device that is used for measurements in gases such as biogas, methane, hydrogen, nitrogen or carbon dioxide. The analyzer meets the requirements of IEC615...
Guildline’s 6623A Series of High Current Range Extenders / Sources is based on patented technology and provides the best in performance and modularity. The 6623A Series consists of a family of range extenders, with available current outputs...
The new Additel 209 and 210 loop calibrator series combine ease of use and functionality, making them the ideal tools to troubleshoot your process loop. The ADT209 has an accuracy of 0.03% of reading whereas the ADT210 holds an accuracy of ...
