-350x280.jpg)
-350x280.jpg)
-350x280.jpeg)
Код: P5523
Brief specifications
Working pressure from 0 to 200 bar
Pressure source required
Pneumatic pressure source connection: 1/4 NPT female
Separator compatible with hydraulic deadweigth tester
NPT and BSP adapter kits included
Not recommended for use with oxygen equipment
More details
For high pressure pneumatic calibrations this unit interfaces with hydraulic deadweight testers providing a rateless liquid-to gas separation. Driven by a pneumatic pressure source (nitrogen bottle) and controlled by needle valves, high pressure gas is balanced against the liquid in a hydraulic deadweight tester through a series of fluid traps.
Note: since fluid mist may be transferred during operation we do not recommend this device for oxygen- safe instruments using an oil operated deadweight tester.
P5523 Liquid-to-Gas Media Separator
- Working pressure: 0 to 200 bar
- Pressure source required
- Pressure source connection: 1/4 NPT
- Compatible with hydraulic piston
- NPT and BSP adapter kits included
/attachments/Fluke_DS/667_P5000SeriesDataSheet_ENG.pdf
Featured Products
Promet EExd Process Moisture Analyzers are hazardous-area rated industrial hygrometer systems for measurement of water vapor content in process gases on natural gas platforms and terminals as well as in petrochemical plants and industrial m...
The PG9607 is the next generation of absolute pressure piston gauge from Fluke Calibration. It supports the use of a 100 kg mass set to define gauge and absolute pressures from 11 to 500 kPa with a single piston-cylinder. The PG9602 is the ...
The PDCR1800 transducer (mV output) and the PTX 1800 transmitter (4 to 20 mA output) are the latest generation of fully submersible titanium high-performance sensors for the measurement of hydrostatic liquid levels. The 1800 Series incorpor...
VMF® – VenturiMasterFlow®
Flow measurement of air and gases
We develop and manufacture venturi tubes and nozzles as individual components or as complete VMF® systems. The VenturiMasterFlow® measuring system, or VMF® for short, is used...
-327x226.jpg)
The ADT912A Pneumatic Pressure Test Pump is a hand operated pressure pump designed to generate pressure from 95% vacuum to 60 psi (4 bar). A high-quality screw press is designed for fine pressure adjustment, with an adjustment resolution up...
-327x226.jpeg)
Isotech calibration baths employ sophisticated designs to ensure calibration to the smallest of uncertainties. In 1986 Isotech purchased the interests of H N Irving & Sons Temperature division which had specialised in providing high quality...
The CRP5 clean-room panel is the obvious choice wherever a high degree of cleanliness is vital, in addition to precise measurement of differential pressure, humidity, and temperature. The CRP5 is used particularly in clean-rooms in hospital...
The Fluke Calibration 6270A
Pressure Controller/Calibrator is a robust, reliable solution that lets you dramatically simplify the task of pneumatic pressure calibration. Thanks to its modular design, it is so flexible that it can be config...
The GPR-1800 series of intrinsically safe trace oxygen analyzers are designed for use in demanding process environments where the low detection limit down the AII’s industrial oxygen sensors can be well utilized. Typical for Analytical Indu...
The HygroFlex3 series is ideal for all applications where good accuracy measurement of humidity and temperature is of critical importance. The transmitters can be used in a wide range of industries...
The piston gauge’s fundamental operating principle and excellent long term stability have made it an indispensable tool in high accuracy pressure metrology. As accuracy levels increase, quality assurance requirements intensify and automatio...
Designed with low cost, portability and ease of use in mind, the 2080 provides on or off site verification of RCD testers, Loop testers, Continuity and Insulation testers and multifunction testers. The 2080 is simple to use and provides the...
GA21 plus
Portable gas analyser GA21 plus is a portable analyser using advanced technologies. It can be equipped with up to 8 electrochemical and NDIR sensors. The analyser has a built-in pressure sensor, large internal memory for result...
-327x226.jpeg)
The purpose of Cal NotePad (CNP) is to automatically log and display the temperature of an Isotech calibration bath together with the unit under test. Cal NotePad can be used with baths (or indicators) without PC interfaces by the user typi...
The 4000 Series is aimed at laboratories, manufacturers and design facilities requiring a wide range of outputs with accuracies up to 8ppm. The 4000 Series builds on the trusted reliability of the 3000A series, offering an updated user inte...
The GPR-3500MO is supplied with panel mounted flow meter for maximum portability...
Isotech produces a miniature resistor with ultra-low temperature coefficient and ultra-high stability. This is achieved because the resistors are oil filled and hermetically sealed. The function of hermetic sealing is to eliminate the ingre...
-327x226.jpeg)
Precision calibration of thermometers calls for the use of stirred liquid calibration baths. The Hydra models set new standards in terms of price to performance ratio. Now Calibration Engineers and Metrologists can choose from a range of ba...
GUILDLINE INSTRUMENTS provides two series of the best performing, most compact, wide-band AC current shunts that are commercially available PRODUCT FEATURES High Current Values to 100 A AC/DC Difference Essentially Zero at Power Frequencies...
Pneumatic hose terminated with quick fit connectors compatible with the test point adaptors supplied with the PV62XG, MC620G and the adaptor sets.
Hazardous area use 1 m/3.28 ft pneumatic hose. Maximum pressure 400 bar/5800 psi...
