-350x280.jpg)
-350x280.jpg)
-350x280.jpeg)
-1000x1000.jpeg "Ice mantle maker for water triple point cells")
Код: Ice mantle
Brief specifications
More details
Are you fed up with cold wet hands, and hours of frustration when you produce an ice mantle in your Triple Point Cell? Change your life and try the Isotech Ice Mantle Maker. It works by using a specially designed anti-gravity heat pipe. The heat pipe exits the cell and exchanges the heat/cool in a small container filled with solid carbon dioxide or preferably liquid nitrogen. Because of the low temperature gradient along the heat pipe the ice mantle is formed close to 0°C, and so beautiful strain free mantles are formed. The Mantle Maker works equally well when you wish to increase the thickness of ice at the bottom of the cell. By keeping only a cc of alcohol in the cell the heat transfer is focused around the bottom of the cell.
Документация
Ice mantle maker for water triple point cells
- Typical time to create a mantle is 20 to 30 minutes
- Are you fed up with cold wet hands, and hours of frustration when you produce an ice mantle in your Triple Point Cell? Change your life and try the Isotech Ice Mantle Maker.
- Specially designed anti-gravity heat pipe
- Create mantle in 20-30 min with Jarrett-Isotech cell
- Option for additional Ice Bridge Prevention Collar
- Form beautiful, strain-free ice mantles
Featured Products
Heat Pipe Furnaces Isotech metrology furnaces have more than 35 years of proven use and are widely used by the worlds’ leading NMIs. For the optimal use of fixed point cells the temperature uniformity should be less than 10mK over the lengt...
-327x226.jpeg)
The Isotech Hydra range of calibration baths have proved very successful since their introduction in 2003. The Orion range has been introduced to fit alongside the Hydra models. The Orion calibration baths offer deeper calibration volumes t...
If you are serious about portable temperature calibration tools, then you know a good dry well calibrator is more than just a stable heat source. The Additel 875 Series Dry Well Calibrators combine excellent performance in stability, radial...
Promet EExd Process Moisture Analyzers are hazardous-area rated industrial hygrometer systems for measurement of water vapor content in process gases on natural gas platforms and terminals as well as in petrochemical plants and industrial m...
The QMA601 Process Moisture Analyzer provides highly reliable, fast and accurate measurement of moisture content in a wide variety of carrier gases. It has a lower detection limit of 0.1 ppmV with reliable accuracy at sub-ppm trace moisture...
This external battery charging station allows a spare battery to be charged independently of the DPI620G for minimum instrument down time. Power is provided by the standard mains adaptor (P/N I0620-PSU). A complete charge cycle takes approx...
-327x226.jpeg)
Need advice on which model? Dry Block Selection Guide These models will calibrate temperature probes from -45°C to 250°C with unrivalled flexibility. As a traditional Dry Block, several thermometers can be quickly calibrated. Accessories ar...
These thermocouples are suitable for use as references in Isotech Dry Blocks and for use with temperature indicators. Details of our laboratory grade Standard Thermocouples with separate cold junctions can be found in our publication “Solut...
The Additel 793 pressure controller combines the latest control/measure technology, modular design and easy to use/maintenance features into a single users friendly device. The Additel 793 provides pressure control up to 15,000 psi (1,000 B...
-327x226.jpg)
The DPI 800 Series is a complete range of advanced, robust and simple to use hand-held instruments. Highly cost effective, these tools are ideal for test/calibration of many popular process parameters. Advanced features and technical innova...
The 919A High Pressure Test Pump is a hand operated pressure pump designed to generate pressure from 95% vacuum to 2,000 psi (140 bar). With a long lever, it just takes 30 seconds to reach 2,000 psi (140 bar). A high-quality screw press is ...
The SF52 dew-point transmitter is a simple, cost effective moisture sensor designed for use in harsh industrial dryer applications. It is reliable and tough enough to withstand the high temperatures often associated with industrial drying.
...
-327x226.jpg)
The PM620 series is the latest development in digital output sensor technology incorporating a number of key innovations to allow pressure re-ranging of compatible equipment. A simple screw fit makes both the pressure and electrical connect...
The Series 7050 digital pressure indicator expands upon the popular line of Series 7000 products such as the Series 7250 digital pressure controller and Series 7252 dual output pressure controller. The 7050 provides an instrument for applic...
The Working Standard WS 2330 is a three-phase precision reference meter for electrical power and energy measurement, dedicated to on-site meter testing. The device provides also function of local data exchange with smart meters (data readou...
Naturally ventilated shields are used where the natural ventilation (wind) suffices, e.g. measurement stations in the mountains...
A set of test point adaptors to connect the tool less quick fit PV62XG, MC620G and the extension hoses to the device under test...
Guildline Instruments 9340-4T Series of precision RTD Simulators and DC Resistance Standards are a complete family of easy to use low to ultra-low, 4 Wire resistance standards offering the best combination of accuracy and resistance range t...
Expert technical support to keep your software up to date and assist with technical issues. Transmille offer software support packages to help you get the most out of your software. Benefits include : Within Version updates (V6.0 to V6.1) D...
GUILDLINE INSTRUMENTS GL 1010 SERIES of Resistance Transfer Standards are very stable and low uncertainty calibration laboratory standards for customers looking to replace the old ESI 1010 series. PRODUCT FEATURES Transfer Accuracy better t...
