-350x280.jpg)
-350x280.jpg)
-350x280.jpeg)
Код: MP100A/MP400A
Brief specifications
More details
The MP100A is a combined humidity and temperature probe designed primarily for meteorological and general outdoor applications. Operation from DC voltage and low power consumption make the MP101A particularly suitable for operation at remote locations. Energizing of the probe is required for only 0.25 seconds during each measurement. The linear output signals are consistent with the requirements of most data acquisition systems.
Meteorology RH and T Probes - Rotronic MP100A/MP400A
-Measurement range: 0..100 %RH
Accuracy at 0...30 °C: 10…95 %RH: ±1.5 %RH
Measurement range: -50...100 °C
Accuracy at 0...30 °C: ±0.3 K
Range of application: -40...85 °C
Featured Products
To calibrate gauges with the pressure connection on the rear (for example, panel mount gauges) in their correct operating position, an angle adaptor should be used. The angle adapter uses the standard gauge adapters and positions the gauges...
Second only to the Water Triple Point and in many ways, because of its ease of use and purity, superior to it, is the Gallium Melt Point. At 29.7646°C this is a very convenient temperature. Total Confidence Confidence is a major requirement...
-327x226.jpg)
Whilst heat pipe furnaces offer the ideal environment to melt and freeze ITS-90 Fixed Points the temperature range is limited by fluid that flows inside the pipe. Three zone furnaces can offer wider operating ranges and still meet the requi...
The Power Source generates and delivers precision high power voltage and current signals for high volume calibration and testing of electricity meters and measuring devices...
-327x226.jpeg)
The function of this reference unit differs from other cased systems in that the temperature of the metal block in which the thermocouple and copper leads are inserted, actually varies with ambient temperature. A separate output signal is p...
Application works as Control Software for products of Applied Precision. It can show measured values, control meter error measurement and generation of signals (in PTE device)...
The PG9607 is the next generation of absolute pressure piston gauge from Fluke Calibration. It supports the use of a 100 kg mass set to define gauge and absolute pressures from 11 to 500 kPa with a single piston-cylinder. The PG9602 is the ...
-327x226.jpeg)
The Isotech Small Hotplate is a lightweight portable calibration system purpose designed for surface mounted sensors. The flat surface plate is made from precision-machined aluminum. The sensor to be tested is simply placed on the surface, ...
-327x226.jpeg)
Download Icarus – Evaluation Download Icarus Data Sheet Download Software Guide Icarus is designed to calculate and display the relationship between resistance and temperature for Standard Platinum Resistance Thermometers between the triple...
-327x226.jpg)
PM620 now incorporates our unique range of TERPS resonant silicon pressure sensor technology, the PM620T and the PM620TS intrinsically safe version. Providing up to four times greater stability and higher accuracy than current pressure meas...
Isotech have a wide range of Dry Blocks to suit probes requiring a large immersion depth. These products feature large and deep calibration volumes. As such they are less portable than the earlier Dry Blocks, but have higher capacities and ...
The HC2A series are digital humidity-temperature probes based on the AirChip3000 technology. These probes
feature a UART serial interface and two 0…1 V linear analog output signals.
The HC2A probes are designed for use with the HygroClip2...
-327x226.jpeg)
Operating principles The problem: Temperature measurement is one of the most demanding applications of resistance measurement. It requires the measurement of resistance ratios to accuracies of 0.1ppm or better. While dc resistance standards...
-327x226.jpeg)
The Gemini R 550 Portable Blackbody Calibration Source allows for calibration of noncontact infrared thermometers over the temperature range 30°C to 550°C. It is suitable for use as a primary radiation source for infrared thermometers. Labo...
GUILDLINE INSTRUMENTS 7810 WIDEBAND TRANSCONDUCTANCE AMPLIFIER is the latest innovation for High Current, Wide Bandwidth AC Outputs. PRODUCT FEATURES 50 A and 100 A Models Calibrated Frequency Range (DC to 100 kHz) Uncalibrated 100 kHz to 2...
The Isothermal range of Thermocouple Standards are the result of many years development. The type R and S standards will cover the range from 0°C to 1600°C. The measuring assembly comprises a 7mm x 300mm or 600mm gas tight 99.7% recrystalli...
-327x226.jpeg)
Need advice on which model? Dry Block Selection Guide These models will calibrate temperature probes from -45°C to 250°C with unrivalled flexibility. As a traditional Dry Block, several thermometers can be quickly calibrated. Accessories ar...
The XB32A OEM transmitter consists of a cable probe and PCB without housing. Thanks to its compact size, high accuracy and various selection
possibilities, the transmitter can be adapted to customer wishes and used practically everywhere...
Simple to use and rugged, the MDM50 high-speed portable hygrometer is the ideal tool for a wide range of on-site maintenance spot checks. The robust integral sample system and fast-response polymer moisture sensor provide a quick, accurate ...
The Model 787 calibrator redefines industry standards by blending industry leading performance and speed of operation within a robust design tailored for extreme conditions. The maximum operating temperature is 660°C allowing wide range of ...
